|
A wind tunnel is a tool used in aerodynamic research to study the effects of air moving past solid objects. A wind tunnel consists of a tubular passage with the object under test mounted in the middle. Air is made to move past the object by a powerful fan system or other means. The test object, often called a wind tunnel model is instrumented with suitable sensors to measure aerodynamic forces, pressure distribution, or other aerodynamic-related characteristics. The earliest wind tunnels were invented towards the end of the 19th century, in the early days of aeronautic research, when many attempted to develop successful heavier-than-air flying machines. The wind tunnel was envisioned as a means of reversing the usual paradigm: instead of the air standing still and an object moving at speed through it, the same effect would be obtained if the object stood still and the air moved at speed past it. In that way a stationary observer could study the flying object in action, and could measure the aerodynamic forces being imposed on it. The development of wind tunnels accompanied the development of the airplane. Large wind tunnels were built during the Second World War. Wind tunnel testing was considered of strategic importance during the Cold War development of supersonic aircraft and missiles. Later on, wind tunnel study came into its own: the effects of wind on man made structures or objects needed to be studied when buildings became tall enough to present large surfaces to the wind, and the resulting forces had to be resisted by the building's internal structure. Determining such forces was required before building codes could specify the required strength of such buildings and such tests continue to be used for large or unusual buildings. Still later, wind-tunnel testing was applied to automobiles, not so much to determine aerodynamic forces ''per se'' but more to determine ways to reduce the power required to move the vehicle on roadways at a given speed. In these studies, the interaction between the road and the vehicle plays a significant role, and this interaction must be taken into consideration when interpreting the test results. In an actual situation the roadway is moving relative to the vehicle but the air is stationary relative to the roadway, but in the wind tunnel the air is moving relative to the roadway, while the roadway is stationary relative to the test vehicle. Some automotive-test wind tunnels have incorporated moving belts under the test vehicle in an effort to approximate the actual condition, and very similar devices are used in wind tunnel testing of aircraft take-off and landing configurations. The advances in computational fluid dynamics (CFD) modelling on high speed digital computers has reduced the demand for wind tunnel testing. However, CFD results are still not completely reliable and wind tunnels are used to verify CFD predictions. ==Measurement of aerodynamic forces== Air velocity and pressures are measured in several ways in wind tunnels. Air velocity through the test section is determined by Bernoulli's principle. Measurement of the dynamic pressure, the static pressure, and (for compressible flow only) the temperature rise in the airflow. The direction of airflow around a model can be determined by tufts of yarn attached to the aerodynamic surfaces. The direction of airflow approaching a surface can be visualized by mounting threads in the airflow ahead of and aft of the test model. Smoke or bubbles of liquid can be introduced into the airflow upstream of the test model, and their path around the model can be photographed (see particle image velocimetry). Aerodynamic forces on the test model are usually measured with beam balances, connected to the test model with beams,strings, or cables. The pressure distributions across the test model have historically been measured by drilling many small holes along the airflow path, and using multi-tube manometers to measure the pressure at each hole. Pressure distributions can more conveniently be measured by the use of pressure-sensitive paint, in which higher local pressure is indicated by lowered fluorescence of the paint at that point. Pressure distributions can also be conveniently measured by the use of pressure-sensitive pressure belts, a recent development in which multiple ultra-miniaturized pressure sensor modules are integrated into a flexible strip. The strip is attached to the aerodynamic surface with tape, and it sends signals depicting the pressure distribution along its surface.〔''Going with the flow'', Aerospace Engineering & Manufacturing, March 2009, pp. 27-28 Society of Automotive Engineers〕 Pressure distributions on a test model can also be determined by performing a wake survey, in which either a single pitot tube is used to obtain multiple readings downstream of the test model, or a multiple-tube manometer is mounted downstream and all its readings are taken. The aerodynamic properties of an object can not all remain the same for a scaled model.〔(Low-Reynolds-Number Airfoils, P.B.S. Lissaman, AeroVironment Inc., Pasadena, California, 91107 )〕 However, by observing certain similarity rules, a very satisfactory correspondence between the aerodynamic properties of a scaled model and a full-size object can be achieved. The choice of similarity parameters depends on the purpose of the test, but the most important conditions to satisfy are usually: * Geometric similarity: all dimensions of the object must be proportionally scaled; * Mach number: the ratio of the airspeed to the speed of sound should be identical for the scaled model and the actual object (having identical Mach number in a wind tunnel and around the actual object is -not- equal to having identical airspeeds) * Reynolds number: the ratio of inertial forces to viscous forces should be kept. This parameter is difficult to satisfy with a scaled model and has led to development of pressurized and cryogenic wind tunnels in which the viscosity of the working fluid can be greatly changed to compensate for the reduced scale of the model. In certain particular test cases, other similarity parameters must be satisfied, such as e.g. Froude number. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Wind tunnel」の詳細全文を読む スポンサード リンク
|